Bird-technologies 5000-XT-Quick Start Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Instruments de mesure Bird-technologies 5000-XT-Quick Start. Bird Technologies 5000-XT-Quick Start User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 9
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
920-5000-XT-QSG Rev A www.bird-electronic.com (866) 695-4569
5000XT DPM Quick Start Guide
Installing the Battery
1. Lay the DPM, display side down, on a clean surface.
2. Remove the two mounting screws from the back cover.
3. Remove the back cover.
4. Install the battery.
5. Replace the back cover.
6. Secure the back cover with the mounting screws.
7. Attach the DPM to an external power source to charge the battery.
8. Charge the battery for five hours before use.
Connecting
Note: If the 5000-XT is connected to a PC when starting or restarting the
PC, it may cause the boot process to lock up. Disconnect the 5000-XT before
starting or restarting the PC.
Note: Use the appropriate Bird Power sensor for the RF power measurement
application. An attenuator may be required.
WARNING
Do not connect to any external power before disassembly.
The potential for electric shock exists.
WARNING
Never attempt to connect or disconnect RF equipment from the transmission line
while RF power is being applied.
Leaking RF energy is a potential health hazard.
RF voltage may be present in RF element socket.
Keep element in socket during operation.
Back Cover
Mounting
Screws
Battery
Vue de la page 0
1 2 3 4 5 6 7 8 9

Résumé du contenu

Page 1 - 5000XT DPM Quick Start Guide

920-5000-XT-QSG Rev A www.bird-electronic.com (866) 695-45695000XT DPM Quick Start GuideInstalling the Battery1. Lay the DPM, display side down, on a

Page 2 - TERMINATING POWER SENSOR

920-5000-XT-QSG Rev A www.bird-electronic.com (866) 695-4569Setting Up1. Connect the sensor.2. Turn on the DPM.3. Zero the sensor (WPS and TPS only).

Page 3

920-5000-XT-QSG Rev A www.bird-electronic.com (866) 695-4569Basic Button FunctionsUpgrading the Firmware1. Power on the 5000-XT 2. Connect the USB fr

Page 4 - Conexión

920-5000-XT-QSG Rev A www.bird-electronic.com (866) 695-4569Guía de inicio rápido del 5000XT DPMInstalación de la batería1. Coloque el DPM, con la pan

Page 5 - GENERADOR

920-5000-XT-QSG Rev A www.bird-electronic.com (866) 695-4569Configuración1. Conecte el sensor.2. Encienda el DPM.3. Coloque el sensor a cero (sólo WP

Page 6

920-5000-XT-QSG Rev A www.bird-electronic.com (866) 695-4569Funciones básicas de los botonesActualización del Firmware1. Encienda el 5000-XT 2. Conec

Page 7 - 5000XT DPM 快速入门指南

920-5000-XT-QSG 修订版 A www.bird-electronic.com (866) 695-45695000XT DPM 快速入门指南安装电池1. 将 DPM 放在清洁表面上,显示屏朝下。2. 从后盖上拆除 2 根安装螺丝。3. 拆除后盖。4. 安装电池。5. 重新安装后盖。6.

Page 8 - 和次要显示器将在 1 到 13 秒的延迟后作出回应。

920-5000-XT-QSG 修订版 A www.bird-electronic.com (866) 695-4569安装1. 连接传感器。2. 开启 DPM。3. 归零传感器 (仅限 WPS 和 TPS)。4. 开启射频源。5. 记录读数。+ 备注: 射频功率出现变化时,模拟条线图将立即作出

Page 9 - 及固件升级信息,请访问:

920-5000-XT-QSG 修订版 A www.bird-electronic.com (866) 695-4569基本按钮功能升级固件1. 开启 5000-XT 2. 将 5000-XT 上的 USB 连接至电脑,待屏幕上出现驱动器。 + 备注: 此过程需 30 秒。3. 创建一个命名为

Commentaires sur ces manuels

Pas de commentaire